Home
Company Profile
E-Mail Address
Product Catalog
Pipes/Tubes
Hollow Sections
Fittings/Flanges
Plates/Sheets/Coils
Hot Rolled Steel Plates
Hot Rolled Steel Sheets
Hot Rolled Coils
Rods/Bars/Wires
Bars For Oil & Gas
Forged Round Bars
Hexagon Bars
Square Bars
Cold Drawn Bars
Forged Disk/Circles
Structural Steels
Flat Bars/Strips
Studs/Bolts/Nuts
Threaded Bars/Rods
Fasteners
SA193 B7 Stud Bolts
SA193 B16 Stud Bolts
SA194 2H HEX NUTS
Corten-A/Corten-B
SAILCOR IRSM41-97
Spring Steel Bars
Boiler/PVQ Plates
Structural Plates
Alloy Steel Plates
Shipbuilding Plates
LRS Grade-A/B Plates
ABS Grade-A/B Plates
DNV Grade-A/B Plates
BV Grade-A/B Plates
SABS 1431:1987 Steels
Q&T Steel Plates
Plate Sizes & Grades
SA516-60/70 HIC Tested
SA516-60/70 Plates
SA515-60/70 Plates
ST52-3 DIN 17100
S355J2G3 EN 10025-2
S355K2G3 EN 10025-2
S355J2+N EN 10025-2
S355K2+N EN 10025-2
EN 10025-2 Plates
EN 10028-2/3 Plates
Abrasion Resistant Steel
Wear Resistant Steel
Hardox 400/450 Plates
Hardox 500/600 Plates
Weldox 700 Plates
SAILMA 350/350HI Plates
SAILMA 410/410HI Plates
SAILMA 450/450HI Plates
Seamless Pipes/Tubes
Welded Pipes/Tubes
ERW/EFW Pipes/Tubes
SAW/HFW Pipes
ASTM A234/ASME SA234
ASTM A403/ASME SA403
ASTM A420/ASME SA420
ASTM A860/ASME SA860
Long Radius Bends
Hot Induction Bends
Forged Fittings
Forged Flanges
API 5L Line Pipes
API 5L Gr.B PSL1/2 Pipes
API 5L X42 PSL1/2 Pipes
API 5L X46 PSL1/2 Pipes
API 5L X52 PSL1/2 Pipes
API 5L X56 PSL1/2 Pipes
API 5L X60 PSL1/2 Pipes
API 5L X65 PSL1/2 Pipes
API 5L X70 PSL1/2 Pipes
High Speed Steels
Cold Work Tool Steels
Hot Work Tool Steels
Plastic Moulding Steels
BS970 Specifications
SAE Specifications
JIS Specifications
ASTM Standard Spec
ASME Standard Spec
Aerospace Alloys Spec
Equivalent Grades
Equivalent Grades
Equivalent Standards
Equivalent Standards
Technical Specifications
DIN Material No.
Mechanical Properties
Mechanical Properties
Chemical Composition
Density
Contact Us
E-Mail Address
Links
News

News 

News

Effects of Elements on Steel

Publish Date 2011-07-14
Effects of Elements on Steel

Steels are among the most commonly used alloys. The complexity of steel alloys is fairly significant. Not all effects of the varying elements are included. The following text gives an overview of some of the effects of various alloying elements. Additional research should be performed prior to making any design or engineering conclusions.

Carbon has a major effect on steel properties. Carbon is the primary hardening element in steel. Hardness and tensile strength increases as carbon content increases up to about 0.85% C as shown in the figure above. Ductility and weldability decrease with increasing carbon.


Manganese is generally beneficial to surface quality especially in resulfurized steels. Manganese contributes to strength and hardness, but less than carbon. The increase in strength is dependent upon the carbon content. Increasing the manganese content decreases ductility and weldability, but less than carbon. Manganese has a significant effect on the hardenability of steel.


Phosphorus increases strength and hardness and decreases ductility and notch impact toughness of steel. The adverse effects on ductility and toughness are greater in quenched and tempered higher-carbon steels. Phosphorous levels are normally controlled to low levels. Higher phosphorus is specified in low-carbon free-machining steels to improve machinability.


Sulfur decreases ductility and notch impact toughness especially in the transverse direction. Weldability decreases with increasing sulfur content. Sulfur is found primarily in the form of sulfide inclusions. Sulfur levels are normally controlled to low levels. The only exception is free-machining steels, where sulfur is added to improve machinability.


Silicon is one of the principal deoxidizers used in steelmaking. Silicon is less effective than manganese in increasing as-rolled strength and hardness. In low-carbon steels, silicon is generally detrimental to surface quality.


Copper in significant amounts is detrimental to hot-working steels. Copper negatively affects forge welding, but does not seriously affect arc or oxyacetylene welding. Copper can be detrimental to surface quality. Copper is beneficial to atmospheric corrosion resistance when present in amounts exceeding 0.20%. Weathering steels are sold having greater than 0.20% Copper.


Lead is virtually insoluble in liquid or solid steel. However, lead is sometimes added to carbon and alloy steels by means of mechanical dispersion during pouring to improve the machinability.


Boron is added to fully killed steel to improve hardenability. Boron-treated steels are produced to a range of 0.0005 to 0.003%. Whenever boron is substituted in part for other alloys, it should be done only with hardenability in mind because the lowered alloy content may be harmful for some applications.


Boron is a potent alloying element in steel. A very small amount of boron (about 0.001%) has a strong effect on hardenability. Boron steels are generally produced within a range of 0.0005 to 0.003%. Boron is most effective in lower carbon steels.


Chromium is commonly added to steel to increase corrosion resistance and oxidation resistance, to increase hardenability, or to improve high-temperature strength. As a hardening element, Chromium is frequently used with a toughening element such as nickel to produce superior mechanical properties. At higher temperatures, chromium contributes increased strength. Chromium is a strong carbide former. Complex chromium-iron carbides go into solution in austenite slowly; therefore, sufficient heating time must be allowed for prior to quenching.


Nickel is a ferrite strengthener. Nickel does not form carbides in steel. It remains in solution in ferrite, strengthening and toughening the ferrite phase. Nickel increases the hardenability and impact strength of steels.


Molybdenum increases the hardenability of steel. Molybdenum may produce secondary hardening during the tempering of quenched steels. It enhances the creep strength of low-alloy steels at elevated temperatures.


Aluminum is widely used as a deoxidizer. Aluminum can control austenite grain growth in reheated steels and is therefore added to control grain size. Aluminum is the most effective alloy in controlling grain growth prior to quenching. Titanium, zirconium, and vanadium are also valuable grain growth inhibitors, but there carbides are difficult to dissolve into solution in austenite.


Zirconium can be added to killed high-strength low-alloy steels to achieve improvements in inclusion characteristics. Zirconium causes sulfide inclusions to be globular rather than elongated thus improving toughness and ductility in transverse bending.


Niobium (Columbium) increases the yield strength and, to a lesser degree, the tensile strength of carbon steel. The addition of small amounts of Niobium can significantly increase the yield strength of steels. Niobium can also have a moderate precipitation strengthening effect. Its main contributions are to form precipitates above the transformation temperature, and to retard the recrystallization of austenite, thus promoting a fine-grain microstructure having improved strength and toughness.


Titanium is used to retard grain growth and thus improve toughness. Titanium is also used to achieve improvements in inclusion characteristics. Titanium causes sulfide inclusions to be globular rather than elongated thus improving toughness and ductility in transverse bending.


Vanadium increases the yield strength and the tensile strength of carbon steel. The addition of small amounts of Vanadium can significantly increase the strength of steels. Vanadium is one of the primary contributors to precipitation strengthening in microalloyed steels. When thermomechanical processing is properly controlled the ferrite grain size is refined and there is a corresponding increase in toughness. The impact transition temperature also increases when vanadium is added.


All microalloy steels contain small concentrations of one or more strong carbide and nitride forming elements. Vanadium, niobium, and titanium combine preferentially with carbon and/or nitrogen to form a fine dispersion of precipitated particles in the steel matrix.




Home  |  Company Profile  |  E-Mail Address  |  Product Catalog  |  Pipes/Tubes  |  Hollow Sections  |  Fittings/Flanges  |  Plates/Sheets/Coils  |  Hot Rolled Steel Plates  |  Hot Rolled Steel Sheets  |  Hot Rolled Coils  |  Rods/Bars/Wires  |  Bars For Oil & Gas  |  Forged Round Bars  |  Hexagon Bars  |  Square Bars  |  Cold Drawn Bars  |  Forged Disk/Circles  |  Structural Steels  |  Flat Bars/Strips  |  Studs/Bolts/Nuts  |  Threaded Bars/Rods  |  Fasteners  |  SA193 B7 Stud Bolts  |  SA193 B16 Stud Bolts  |  SA194 2H HEX NUTS  |  Corten-A/Corten-B  |  SAILCOR IRSM41-97  |  Spring Steel Bars  |  Boiler/PVQ Plates  |  Structural Plates  |  Alloy Steel Plates  |  Shipbuilding Plates  |  LRS Grade-A/B Plates  |  ABS Grade-A/B Plates  |  DNV Grade-A/B Plates  |  BV Grade-A/B Plates  |  SABS 1431:1987 Steels  |  Q&T Steel Plates  |  Plate Sizes & Grades  |  SA516-60/70 HIC Tested  |  SA516-60/70 Plates  |  SA515-60/70 Plates  |  ST52-3 DIN 17100  |  S355J2G3 EN 10025-2  |  S355K2G3 EN 10025-2  |  S355J2+N EN 10025-2  |  S355K2+N EN 10025-2  |  EN 10025-2 Plates  |  EN 10028-2/3 Plates  |  Abrasion Resistant Steel  |  Wear Resistant Steel  |  Hardox 400/450 Plates  |  Hardox 500/600 Plates  |  Weldox 700 Plates  |  SAILMA 350/350HI Plates  |  SAILMA 410/410HI Plates  |  SAILMA 450/450HI Plates  |  Seamless Pipes/Tubes  |  Welded Pipes/Tubes  |  ERW/EFW Pipes/Tubes  |  SAW/HFW Pipes  |  ASTM A234/ASME SA234  |  ASTM A403/ASME SA403  |  ASTM A420/ASME SA420  |  ASTM A860/ASME SA860  |  Long Radius Bends  |  Hot Induction Bends  |  Forged Fittings  |  Forged Flanges  |  API 5L Line Pipes  |  API 5L Gr.B PSL1/2 Pipes  |  API 5L X42 PSL1/2 Pipes  |  API 5L X46 PSL1/2 Pipes  |  API 5L X52 PSL1/2 Pipes  |  API 5L X56 PSL1/2 Pipes  |  API 5L X60 PSL1/2 Pipes  |  API 5L X65 PSL1/2 Pipes  |  API 5L X70 PSL1/2 Pipes  |  High Speed Steels  |  Cold Work Tool Steels  |  Hot Work Tool Steels  |  Plastic Moulding Steels  |  BS970 Specifications  |  SAE Specifications  |  JIS Specifications  |  ASTM Standard Spec  |  ASME Standard Spec  |  Aerospace Alloys Spec  |  Equivalent Grades  |  Equivalent Grades  |  Equivalent Standards  |  Equivalent Standards  |  Technical Specifications  |  DIN Material No.  |  Mechanical Properties  |  Mechanical Properties  |  Chemical Composition  |  Density  |  Contact Us  |  E-Mail Address  |  Links  |  News  |  Sitemap  |  Mobile Version
Powered by DIYTrade.com